Oil & Gas Process Engineering

Skip to content
Menu
  • Home
  • Contact Us
  • Privacy Policy
  • Terms

Category: Centrifugal Pumps Bearings-Seals-Wear-Rings

Centrifugal Pumps Bearings-Seals-Wear-Rings

Wear Rings

Posted on September 12, 2009

These are easily renewable leakage seals between the impeller or shaft and casing designed to prevent leakage from high pressure to low pressure areas. They…

Centrifugal Pumps Bearings-Seals-Wear-Rings

Seals

Posted on September 11, 2009

Seals are necessary to prevent leakage at the point where the shaft enters the pump case. The most inexpensive seal is made of packing material…

Centrifugal Pumps Bearings-Seals-Wear-Rings

Bearings

Posted on September 11, 2009

Ball bearings transmit a load from a rotating surface to a fixed surface via a series of rotating balls. They are generally inexpensive, do not…

Pages

  • Contact Us
  • Privacy Policy
  • Terms

Categories

  • Acid Gas Treating
  • Basic Configuration
  • Basic Principles
  • Centrifugal Compressors
  • Centrifugal Pumps
  • Centrifugal Pumps Bearings-Seals-Wear-Rings
  • Characterizing the Flow Stream
  • Chemical Process
  • Chemical Solvents
  • Choise Of Process
  • Coil Sizing
  • Compressors
  • Condensate Stabilization
  • Controlling Pulsating Flow
  • Cooling and Lubricating System
  • Crude Oil Treating System
  • Cylinder Sizing
  • Design Considerations
  • Design Considerations
  • Design Procedures for Amine System
  • Direct Conversion of H2S to Sulfur
  • Emulsion Treating Teory
  • Flotation Units
  • Fluid Properties – Basic Principles
  • Fractions from atmospheric and vacuum distillation
  • Gas
  • Gas Dehydration
  • Gas Processing
  • Gas Sweetening Processes
  • Gas Turbine
  • Generic Types of Centrifugal Pumps
  • Glycol Dehydration
  • Glycol Dehydration
  • Gravity Separation
  • Heat Exchangers
  • Hydrates
  • Ideas To Enhance Gas Flow
  • Influent Water Quality
  • Installation
  • Instrumentation
  • Liquid Loading
  • LTX Units and Line Heaters
  • Mechanical Design of Pressure Vessels
  • Mechanisms of Heat Transfer
  • Oil and Gas Processing
  • Oil and Water Separation
  • Oil Production Facility
  • Petrochemical
  • Physical Solvent Processes
  • Potential Operating Problem
  • Pressure Drop in Piping
  • Pressure Relief
  • Pressure Relieving Systems GP
  • Pressure Vessels – Design
  • Process Cooling in Remote Location
  • Process Heat Duty
  • Produced Water Treating System
  • Production Process Component
  • Pumps
  • Reboiler
  • Reciprocating Compressors
  • RECIPROCATING COMPRESSORS
  • Reciprocating Compressors – Components
  • Refining
  • Relief Valve Sizing
  • Separation
  • Shell and Tube Exchangers
  • Solid Bed Absorption
  • Solid Bed Dehydration
  • Specification and Design
  • Three Phase Separator Sizing
  • Tower Pressure
  • Tray
  • Trays and Packing
  • Treater Vessels Sizing
  • Treating Equipment
  • Two Phase Oil and Gas Separation
  • Two Phase Separator Equipment
  • Two Phase Separator Sizing
  • Two Phase Separator Theory
  • Type Of Devices
  • Types Of Compressors
  • Uncategorized
  • Water Treating Equipment
  • Water Treating Theory
  • Well Site Troubleshooting
  • Wellhead Compression
  • Wellhead Surface Equipment

Recent Posts

  • Receiver Pressure Gages
  • Pneumatic Pressure Transmitters
  • Electronic Pressure Transmitters
  • Field Pneumatic Pressure Controllers
  • Field Pressure Recorders
© Copyright 2023 – Oil & Gas Process Engineering
Wisteria Theme by WPFriendship ⋅ Powered by WordPress